• 青岛欣大荣数控机器有限公司
  • 地址:青岛市城阳区仙山东路北
  • 电话:13791821849
  • 联系人:唐经理
  • 网址:www.qdxdrsk.com
新闻中心当前位置:首页-新闻中心
    关于雕刻机机器错位的解决办法
    2016-1-5 19:17:53
    关于雕刻机机器错位的解决办法:
    About the engraving machine machine dislocation solution:
    1、雕刻机横梁上到机器控制箱衔接拖链的线是不是有接触不良;定制家具生产线
    1, on the beam engraving machine to machine control box cohesion is the line of drag chain has poor contact;
    2、水冷主轴电机前上方的联轴器是不是松动损坏 可查看用手拧紧或许替换
    2, before the water-cooled spindle motor at the top of the loose coupling is damaged To view tight may replace by hand
    3、电脑是不是有病毒或许与其他不兼容或许搅扰,通常主张无须品牌机 简略拼装机箱即可
    3, computer have virus maybe with other incompatible maybe trouble, usually without name-brand computer A brief assembly case
    4、电压的疑问:雕刻机在作业时需求的功率大,若是电压过低,给驱动器供电缺乏,功率达不到则会形成错位表象,这种状况通常以Y轴错位为多,呈现这种表象有可能是外界电压不行,或许在同一线路上有人使用了大功率的设备如电焊等。
    4, voltage, carving machine during operation demand of large power, if the voltage is too low, given the lack of drive power supply, power short of dislocation will form representation, this kind of situation usually Y axis misalignment, is not present this appearance is probably the external voltage, perhaps someone on the same line using the large power equipment such as electric welding, etc.
    处理办法:装置一个5000瓦的稳压电源,但这个稳压电源的差错规模不能超过5%,最好在3%以内。
    The solution: a regulated power supply 5000 watts, but the error scale regulated power supply can't more than 5%, the best within 3%.
    5、驱动器的疑问:驱动器自身里边的布局或许电子原器材有疑问也会形成错位表象,这个缘由最多;
    5, drive, the layout of the inside the drive itself may be electronic original equipment have questions will form the dislocation appearances, the reason most;
    若呈现的次数不多,并且把速度下降一点,有时能正常雕琢,这阐明驱动器还没有完全坏掉;若是一开始雕琢就错位就阐明驱动器完全坏了。
    If the number of times few, and slow down a little, sometimes to carve, clarify this drive is not completely broken. If a began to carve dislocation drive is elucidated completely bad.
    处理办法:修补驱动器或许替换驱动器。

    The solution: repair drives may replace the drive.

    本文由定制家具生产线有限公司发表提供,更多详情请关注公司网址:http://www.qdxdrsk.com/

网站首页 | 公司简介 | 服务项目 | 新闻中心 | 工程案例 | 服务流程 | 在线留言 | 联系我们
版权所有:青岛欣大荣数控机器有限公司  手机:13791821849  电话:唐经理  地址:青岛市城阳区仙山东路北
流量统计:  


销售一部


售后支持
售后支持